Version=5

;postcuring: 

[General]
Name="CRS Custom Denture Resin"
Heater Temperature=35 ;target (heats during print)
Minimum Temperature=32 ;start of print (printer waits until this temp is reached)
Heater Enable=true

[Cure]
Temperature=0
Minimum Temperature=0
Dose=4.70
Power Level=50
Vacuum=true
Vacuum Target=0.030
Minimum Vacuum=0.030
Gas=false
Gas Cycles=1

[:/Gen-2UV/General]
Printer Classes=["Pico UV385", "PRO UV385", "MAX UV385", "PRO 4K UV385", "ULTRA", "MAX 2"] ;remove machines oyu did not validate

[:/Gen-2UV/Curing]
Light Intensity=8 ;maximum light intensity
;Support Exposure=100 ;increase to overcure supports

;MAX UV @ 6.80 mW/cm²
Z	=	[	6.80	,	0.04	,	6.80	]
Z	=	[	8.84	,	0.06	,	6.80	]
Z	=	[	10.20	,	0.08	,	6.80	]
Z	=	[	12.24	,	0.10	,	6.80	]
Z	=	[	13.60	,	0.11	,	6.80	]
Z	=	[	15.64	,	0.13	,	6.80	]
Z	=	[	17.00	,	0.15	,	6.80	]
Z	=	[	19.04	,	0.16	,	6.80	]
Z	=	[	20.40	,	0.17	,	6.80	]
Z	=	[	27.20	,	0.21	,	6.80	]
Z	=	[	34.00	,	0.23	,	6.80	]
Z	=	[	40.80	,	0.25	,	6.80	]
Z	=	[	47.60	,	0.26	,	6.80	]
Z	=	[	54.40	,	0.27	,	6.80	]
Z	=	[	68.00	,	0.29	,	6.80	]
Z	=	[	102.00	,	0.35	,	6.80	]
Z	=	[	136.00	,	0.38	,	6.80	]
Z	=	[	170.00	,	0.40	,	6.80	]
Z	=	[	204.00	,	0.42	,	6.80	]
Z	=	[	238.00	,	0.44	,	6.80	]





Offset=0.1 ;
Z Compensation=0  ;should be positive, remove this value completely from INI if Z Comp should automatically be equal to the Offset
Burn-In Layers=2
Burn-In Exposure=0.23   ;reduce if sticking too hard, increase if doesnt attach properly
Scale=[1.0057, 1.0057, 1.000]     ;shrinkage compensation
XY Compensation=-0.002   ;bleeding in XY compensation, should be negative


[General]
; Uncomment the following line to use sliderless mode as default for PRO
Printer Classes=["Pico UV385", "PRO UV385", "MAX UV385", "PRO 4K UV385"]

[Delays]
Burn-In Wait Time (After Exposure)=0.1 ; s
Burn-In Wait Time (After Separation)=5 ; s ; for material flowback
Burn-In Wait Time (After Approach)=2 ; s
Burn-In Wait Time (After Slide)=0 ; s
Normal Wait Time (After Exposure)=0.1 ; s
Normal Wait Time (After Separation)=0.1 ; s ; for material flowback
Normal Wait Time (After Approach)=0.5 ; s
Normal Wait Time (After Slide)=0 ; s

[:/4K/Mechanics]
Burn-In Separation Velocity= 1.5; mm/s
Separation Velocity= 4.3; mm/s
Approach Velocity= 4.3; mm/s
Separation Acceleration=0.2 ;mm/s
Separation Pressure Limit=300
Viscosity Range=1  ;you can measure this value in material test

[:/Not-4K/General]
Printer Classes=["Pico UV385", "PRO UV385", "MAX UV385"]
Slice Thickness Presets=[0.05,0.075,0.1]
Slice Thickness Preset= 0.050

[:/Not-4K/Mechanics]
Separation Distance=10 ; mm
Burn-In Separation Velocity= 1.5; mm/s
Separation Velocity= 4.3; mm/s
Approach Velocity= 4.3; mm/s
;Separation Acceleration=0.3 ;mm/s
Separation Pressure Limit=300
Viscosity Range=1  ;you can measure this value in material test

[:/4K/General]
Printer Classes=["PRO 4K UV385"]
Slice Thickness Presets=[ 0.05,0.075,0.1]
Slice Thickness Preset= 0.050

[:/4K/Mechanics]
Burn-In Separation Velocity= 1.5; mm/s
Separation Velocity= 4.3; mm/s
Approach Velocity= 4.3; mm/s
Separation Acceleration=0.2 ;mm/s
Separation Pressure Limit=300
Viscosity Range=1  ;you can measure this value in material test

[:/PRO-Platform/General]
Printer Classes=["PRO UV385", "PRO UV405"]
Slice Thickness Presets=[0.05, 0.075, 0.1]
Slice Thickness = 0.05

[:/PRO-Platform/Mechanics]
Separation Distance=10 ; mm
Burn-In Separation Velocity= 1.5; mm/s
Separation Velocity= 4.3; mm/s
Approach Velocity= 4.3; mm/s
Slides Per Layer=0 ;

[Support]
Leveling=true
Leveling Height=2.0
Tallest=true
Tallest Height=8
Slope=45
Side Feature=2.0
Spacing=2.5
Strength=40
Torsion=0
Intersupport=false
Contact=0.4
Island=1.240
Overshoot=1.5
MaximumWidth=3
Side Faces=20
AspectRatio=2.0